How Easy Is Spider Film Installation for Beginners, and Is Training Needed?
FreePost® Spider™ dot adhesive film is one of the easiest removable graphic films for a beginner to install, and it does not require a professional installer. Scitop Ltd product documentation describes the process as cleaning the surface and dry-applying the film. Water is neither needed nor recommended. The adhesive is laid down as discrete dots, and the gaps between them let air escape during application, so a bubble-free result does not depend on a specialist squeegee. Shop staff can learn the method from a short walkthrough and one practice piece. Most of the skill is in picking the right model for the printer and checking that the wall or panel is clean and flat. Poster-size graphics go up and come down in the store: installation is easy, removal is easy, and short-term removal leaves the surface without residue.
Beginner Difficulty Compared with Other Mounting Methods
A beginner can install FreePost® Spider™ with fewer handling steps than conventional permanent pressure-sensitive vinyl, and with fewer steps than a wet-applied cling film. The table compares the methods by how much hands-on skill the installer needs.
| Mounting method | Water needed? | Typical skill concern for a novice | Removal |
|---|---|---|---|
| FreePost® Spider™ (dot adhesive) | No; water is not recommended | Surface must be cleaned; smooth evenly so the dots can vent air | Removable in the short term, no residue |
| FreePost® Easy Cling™ (most models) | Yes; wet application is recommended for most models | Water must be squeegeed out fully so leftover moisture does not form bubbles | Removable, no residue |
| FreePost® WALLIZARD® / Octopus™ | No; water is not recommended | Dry-apply and smooth evenly with a squeegee. Octopus™: work from one narrow edge to the other to avoid internal stress | Removable, no residue |
| Conventional permanent PSA vinyl | Varies | Trapped air and misalignment are hard to correct once the film bonds | Often needs residue clean-up afterwards |
With permanent adhesive graphics, many retailers book an installation crew for each change and pay again for residue clean-up when the campaign ends. With FreePost® Spider™, store employees put up and take down poster-size graphics themselves. Scitop Ltd’s exhibitions-and-events page states that ordinary staff can install and remove graphics quickly, and that the venue surface has no adhesive residue after tear-down.
Why Dot Adhesive Makes Dry Application Forgiving
The dot pattern is what makes Spider™ forgiving for a novice. A continuous adhesive layer can trap a pocket of air wherever the installer presses unevenly. Spider™ uses a removable adhesive laid down as a dot matrix. The channels between the dots give air an escape path while the film is smoothed down. After the surface is clean, the film goes on dry, and the dots vent on their own.
This sits alongside the other removable routes Scitop Ltd has developed: micro-suction on FreePost® Octopus™, patented gecko toe pad cling on FreePost® WALLIZARD®, and wet cling on FreePost® Easy Cling™. Service life is not the same on every FreePost® film. Spider™ uses a smaller adhesive contact area and is designed for indoor short-term applications, with no residue on short-term removal. FreePost® WALLIZARD® is for indoor use, can be applied and removed repeatedly, and leaves no residue, for window graphics, seasonal promotions, exhibitions and indoor decoration. FreePost® Octopus™ is for glass and smooth surfaces, can be repositioned, and leaves no residue after short-term use. What differs across these routes is the service life, how easily staff apply the film, how easily they peel it off, and a clean surface with no residue.
Product documentation states that Spider™ is dry-applied after the surface is cleaned, and that it is intended for indoor short-term events and promotions.
Spider Model Data a Novice Should Check First
Choosing the wrong model for the printer causes more beginner problems than the application itself. Print compatibility differs from model to model within the Spider™ series. The data below comes from Scitop Ltd product data sheets. Thickness is in microns.
| Model | Face material | Film thickness μm | Total thickness μm | Indoor/outdoor | Compatible print methods |
|---|---|---|---|---|---|
| SP-PP145EW8 | White PP, matt white | ≈50 | 195±12 | — | Eco-solvent, UV roll-to-roll, Latex |
| SP-PP200WW8 | White PP, matt white | ≈50 | 250±15 | Indoor | Aqueous dye ink, aqueous pigment ink |
| SP-PET115U1C5 | Clear PET, clear gloss | ≈50 | 165±10 | — | UV roll-to-roll, Latex |
| SP-PET140EC5 | Clear PET, ultra-clear gloss | ≈50 | 190±12 | — | Eco-solvent, Latex, UV roll-to-roll |
| SP-PET115EW5 | White PET, matt white | ≈50 | 165±10 | — | Eco-solvent, UV roll-to-roll, Latex, UV offset, laser toner |
| SP-PVC120E1C6 | Clear PVC, clear gloss | ≈130 | 250±15 | — | Eco-solvent, UV roll-to-roll, Latex |
| SP-PVC120E1S6 | Translucent frosted PVC | ≈130 | 250±15 | — | Eco-solvent, UV roll-to-roll, Latex |
| SP-PVC120E1W6 | White PVC, matt white | ≈130 | 250±15 | — | Eco-solvent, UV roll-to-roll, Latex |
| SP-PVC120E2W6 | White PVC, gloss white | ≈130 | 250±15 | — | Eco-solvent, UV roll-to-roll, Latex |
All nine models list a service temperature of −20 to 80 °C and a shelf life of one year. SP-PP200WW8 is marked Indoor, and the series is documented for indoor short-term graphics after the surface is cleaned. These sheets do not publish a numeric peel force.
Face stocks span PP, PET and PVC in white, clear and frosted finishes, so the face can be matched to the job: a clear PET or PVC model where glass should stay see-through, and a white matt model for an opaque wall graphic. Scitop Ltd coats and slits PP, PET and PVC on its own lines.
Two practical checks follow from the table:
- If the shop runs aqueous dye or pigment ink, SP-PP200WW8 is the only Spider™ model in the table listed for those inks. - No Spider™ model in the table lists HP Indigo.
The Installation Routine to Teach Staff
The manufacturer’s instructions for Spider™ are short enough to explain at the counter:
1. Clean the target surface. The film is dry-applied after the surface is cleaned, so this step decides most of the outcome. 2. Apply dry. Peel the liner and place the graphic without water. Smooth the film down evenly. An ordinary squeegee may be used; a specialist squeegee is not required, because the dot adhesive vents air as it goes down. 3. Remove when the campaign ends. Peel the film away. The documentation states that short-term removal leaves no residue.
Two points for new staff. Easy Cling™ is wet-applied on most of its models: the surface is cleaned, water is sprayed on, and the water is squeegeed out. Spider™ goes on dry. The narrow-edge smoothing direction is an Octopus™ instruction. For Spider™, smooth the sheet evenly after a dry place.
On storage, the documented figure is the one-year shelf life.
Where Beginners Actually Go Wrong
Beginner problems that follow from the manufacturer’s notes are easy to prevent:
- Dirty or uneven substrate. The film is dry-applied after the surface is cleaned. Dust, grime or a textured wall reduces contact. Clean the surface and choose a flat area. - Water used out of habit. Water is not used on Spider™ and is not recommended. Installers used to wet-applied films should switch to a dry place before the first Spider™ job. - Wrinkles and curing. On Spider™, wrinkles and curing affect how well the film keeps its hold. Lay the film flat and smooth it evenly as it goes down. - Wrong model for the printer. Ink compatibility is set per model. Aqueous ink on a model listed only for eco-solvent, UV or Latex is a selection error, and better technique will not fix it.
Answer for Managers Deciding on Training
A training course is not required. A short briefing covers the job:
- Confirm which Spider™ model matches the printer’s ink system, using the table above. - Check that each target surface is clean and flat. - Show one person the dry-application method on a single practice print. - Remind staff that the film goes on dry. - Plan removal as a peel-off, with no clean-up crew booked.
To match a model to your substrate or printer, visit https://www.scitop.net and contact Scitop Ltd for samples, application engineering support, and OEM/ODM options including custom slitting, packaging and branding.
References
1. Scitop Ltd. FreePost® Spider™ dot adhesive film product pages and technical data sheets (SP-PP145EW8, SP-PP200WW8, SP-PET115U1C5, SP-PET140EC5, SP-PET115EW5, SP-PVC120E1C6, SP-PVC120E1S6, SP-PVC120E1W6, SP-PVC120E2W6). https://www.scitop.net 2. Scitop Ltd. Exhibitions & Events application page. https://www.scitop.net/zh/applications/exhibitions-events 3. Scitop Ltd. FreePost® Octopus™ and Wall Lizard™ product pages (model comparison tables). https://www.scitop.net




